[ENA MICRO 5] Remove front spout
Posted by: jeremy_dmd January 30, 2024 11:38 am
Hello,
When I make a coffee with 2 cups, the right nozzle flows much less than the left nozzle.
Does anyone know how to remove the cover so that the nozzles can be cleaned?
Thanks in advance
Jérémy
Posted by: jeremy_dmd January 30, 2024 11:45 am
I'm talking about this part:
https://ibb.co/Wv17TsR
Or if anyone has a photo of the disassembled cover, to see how it holds, I'm also a taker!
Posted by: kaffeechris January 31, 2024 07:03 pm
You can remove this part manually. But it is also very difficult if it is dirty.
So press in the plastic riffle on the side a little and pull it out at the bottom towards the front.
Then you can remove the plastic part upwards.
Everything else is self-explanatory
Posted by: jeremy_dmd February 04, 2024 06:22 pm
Hello and thank you Kaffeechris!
I managed to disassemble the bottom, quite easy when you have the method (without you I never would have found).
However, the top piece does not come off, it is clipped?
Posted by: Guest February 04, 2024 06:36 pm
And a small picture for those who want to see how it's assembled.
I managed by turning the nozzles to "1 coffee" mode, using a small screwdriver to slightly pry (without forcing) the shiny part.
https://ibb.co/3vyRnVc
Posted by: jeremy_dmd February 04, 2024 06:38 pm
the photo is really small, I repost, sorry I could not edit the old post.
https://ibb.co/3vyRnVc
Posted by: Gast_max May 08, 2024 03:54 pm
Hello, thank you for the previous exchanges which helped me a lot.
I was also able to disassemble the black plastic top part .... But I can't put it back together!
Could you help me?
Posted by: Gast_max May 08, 2024 03:56 pm
Hello, thank you for the previous exchanges which helped me a lot.
I was also able to disassemble the black plastic top part .... But I can't put it back together!
Could you help me?
Posted by: Gast_max May 08, 2024 04:00 pm
Hello, thank you for the previous exchanges which helped me a lot.
I was also able to disassemble the black plastic top part .... But I can't put it back together!
Could you help me?
Posted by: Gast_max May 08, 2024 04:07 pm
Hello, thank you for the valuable instructions above.
I managed to disassemble the black plastic top piece by pulling on it...But I can't get it back on!
Can anyone help me?
Thank you.
Posted by: Ryan June 30, 2024 07:01 pm
Hey guys I'm trying to clean my spouts and can't figure out how to get this thing off. Can it only be done with the spout removal tool? How did you successfully take this off without the spout removal tool?
Is the plastic riffle you are talking about the black circular belt/ring or the part below that with the metallic side pieces that the spouts come through?
I found these instructions also but they require the spout removal tool it seems
Page 1 https://www.manualslib.com/manual/1955269/Jura-Ena-Micro-Series.html?page=15#manual
Page 2 https://www.manualslib.com/manual/1955269/Jura-Ena-Micro-Series.html?page=16#manual
Posted by: pvandorssen July 19, 2024 08:49 pm
Good evening everyone,
I have the same problem and have not yet found out how to remove the spout without the key.
Is the spout only held in place by the thin O-ring?
Piet
Bean2cup.org > Jura > [ENA MICRO 5] Remove front spout